Cross Laminated Timer (CLT) is a prefabricated, solid engineered mass timber panel. CLT is manufactured with kiln-dried lumber boards or structural composite lumber (SCL) laminated in alternating directions and bonded with structural adhesives to form a solid, straight, rectangular panel. Panels are comprised of an odd number of layers, usually three to seven.
While at the mill, CLT panels are cut to size, including door and window openings, with a state-of-the-art CNC router that can make complex cuts with high precision. CLT panel size varies by manufacturer, but typical widths are 2 ft., 4 ft., 8 ft., and 10 ft., with a thickness of 20” or less and a length of up to 60 ft.
CLT is frequently used in multistory mass timber structures, with concrete podiums and other types of buildings.
CLT may be used in the construction of a wide variety of structural elements, such as structural and non-structural wall elements; floor/ceiling, parapet wall and roof elements; pre-insulated wall and roof sections; and solid partitions with or without interior finishes.
CLT’s high load-bearing properties extend its applicability to the construction of bridges, carports, ancillary buildings and wood/concrete composite ceilings. Other applications include cantilevered floors/balconies, load-bearing elevator shafts, and stairs.
Cross-laminated timber is proving to be a highly advantageous alternative to conventional materials like concrete, masonry or steel, especially in multifamily and commercial construction.
When selecting and specifying CLT, there are several key characteristics to consider, including allowable design capacities, grades, laminations and adhesives.
There are five basic “E” grades, six “V” grades and three “S” grades for CLT products and layups. “E”, “V” and “S” indicate a CLT grade with layup of E-rated or machine stress rated (MSR) laminations, visually graded laminations or structural composite lumber (SCL) in the longitudinal layers, respectively. Visually graded or SCL laminations are used in the transverse layers for both “E” and “V” grades and “S” grades, respectively. Custom layups of CLT are also permitted, as stipulated in ANSI/APA PRG 320, Standard for Performance-Rated Cross-Laminated Timber.
The allowable stress design (ASD) reference design capacities for CLT grades with layups of three, five and seven layers are shown in ANSI/APA PRG 320. The ASD reference design capacities for different CLT products are typically published in APA Product Reports or manufacturers’ literature.
Chapter 10 of the 2018 National Design Specification (NDS) provides design procedures, reference design values and other information for CLT, while engineering design of connections using dowel-type fasteners in CLT is covered in Chapter 12 of the 2018 NDS. Sections were also added to the 2018 and 2015 International Building Code and International Residential Code regarding CLT used as different structural elements. Clause 8 in the Canadian Standards Association CSA O86-19 provides design procedures, resistance values and other information for CLT used in Canada.
Any softwood lumber species or species combinations recognized by American Lumber Standards Committee under PS 20 or Canadian Lumber Standards Accreditation Board under CSA O141 with a minimum published specific gravity of 0.35 are permitted for use in CLT, provided that other requirements specified in ANSI/APA PRG 320 are satisfied. SCL should meet the requirements of ASTM D5456, Standard Specification for Evaluation of Structural Composite Lumber Products, and have an “equivalent specific gravity” of 0.35 or higher.
Lumber grades are required to be at least 1200f-1.2E MSR or visually graded No. 2 in the longitudinal layers and visual graded No. 3 in the transverse layers.
Moisture content is required to be 12 ± 3% for lumber and 8 ± 3% for SCL at the time of CLT manufacturing unless a lower moisture content is specifically qualified in accordance with the standard.
In the U.S., adhesives used for CLT manufacturing are required to meet ANSI 405, Standard for Adhesives for Use in Structural Glued Laminated Timber, with the exception that some gluebond durability tests are not required. This is because CLT manufactured according to ANSI/APA PRG 320 is limited to dry service conditions, and some gluebond durability tests are designed for adhesives in exterior applications. In Canada, CLT adhesives must meet the requirements of CSA O112.10. In both the U.S. and Canada, CLT adhesives must meet ASTM D7247 for heat durability and CSA O177, small-scale flame test. In addition, CLT adhesives must comply with the requirements for elevated temperature performance in accordance with the full-scale compartment fire test specified in Annex B of ANSI/APA PRG 320.
CLT shall be furnished and installed in accordance with the recommendations provided by the CLT manufacturer and the engineering drawing approved by the engineer of record. Permissible details shall be in accordance with the engineering drawing.
– Find more information on the selection and specification of structural engineered wood products in the APA Engineered Wood Construction Guide, available as a free download at www.apawood.org.
US LBM has reached a definitive agreement to acquire Foxworth-Galbraith Lumber Co., Plano, Tx.
Growing redwoods for the future was the original tagline for Big Creek Lumber and now 76 years later, they are excited to also be growing their lumberyard locations with the addition of a sixth retail lumber and Ace hardware store. Big Creek Lumber is in the process of acquiring O’Connor Lumber in Vallejo, Ca., and the name will be changed to Big Creek Lumber when the sale is finalized.
Shur-Line’s new 9” Deck Pad with Detail Edge is faster than a roller, smoother than a brush.
US LBM has reached a definitive agreement to acquire Foxworth-Galbraith Lumber Co., Plano, Tx.
Growing redwoods for the future was the original tagline for Big Creek Lumber and now 76 years later, they are excited to also be growing their lumberyard locations with the addition of a sixth retail lumber and Ace hardware store. Big Creek Lumber is in the process of acquiring O’Connor Lumber in Vallejo, Ca., and the name will be changed to Big Creek Lumber when the sale is finalized.
Shur-Line’s new 9” Deck Pad with Detail Edge is faster than a roller, smoother than a brush.
Your industry leading lumber and building materials resource – since 1922.